|Joe Marcus Clarke||Feb 28, 2010 12:23 pm|
|Weongyo Jeong||Mar 1, 2010 3:36 pm||.diff|
|Joe Marcus Clarke||Mar 1, 2010 8:50 pm|
|Weongyo Jeong||Mar 3, 2010 2:04 pm|
|Joe Marcus Clarke||Mar 3, 2010 2:45 pm|
|Weongyo Jeong||Mar 3, 2010 3:13 pm|
|Joe Marcus Clarke||Mar 3, 2010 9:11 pm|
|Weongyo Jeong||Mar 5, 2010 12:53 pm|
|Joe Marcus Clarke||Mar 5, 2010 1:44 pm|
|Weongyo Jeong||Mar 5, 2010 4:16 pm||.diff|
|Joe Marcus Clarke||Mar 6, 2010 9:05 pm|
|Weongyo Jeong||Mar 8, 2010 5:32 pm|
|Joe Marcus Clarke||Mar 13, 2010 4:52 pm|
|Subject:||Re: Problem with new bwn driver on -CURRENT|
|From:||Weongyo Jeong (weon...@gmail.com)|
|Date:||Mar 3, 2010 3:13:53 pm|
On Wed, Mar 03, 2010 at 05:46:09PM -0500, Joe Marcus Clarke wrote:
On 3/3/10 5:04 PM, Weongyo Jeong wrote:
On Mon, Mar 01, 2010 at 11:50:43PM -0500, Joe Marcus Clarke wrote:
On Mon, 2010-03-01 at 15:37 -0800, Weongyo Jeong wrote:
On Sun, Feb 28, 2010 at 03:24:28PM -0500, Joe Marcus Clarke wrote:
I was extremely pleased to see this driver, so I could get off of the flaky NDIS version. I have a Dell Vostra 2510 with a LP bwn mini-PCI card. I have set if_bwn_load="YES" in /boot/loader.conf. I also have bwn_v4_lp_ucode_load="YES" set.
The firmware and driver loads. However, if_bwn doesn't attach to the card. Once the OS is fully booted, I kldunload if_bwn, then reload it, and the driver attaches just fine.
This issue is reported by some people and I'm looking codes.
Good to know.
This issue is solved in r204657. Thank you for reporting!
Saw that, thanks!
bwn0: out of bounds of the square-root table (-770884) bwn0: out of bounds of the square-root table (-225625) bwn0: out of bounds of the square-root table (-240100)
Patch is attached with email and it'll fix this message. Could you please test with it?
Yes, the patch removes those messages. Thanks!
Was this patch committed? I don't recall seeing an svn notice.
Yes at r204542.
Was it successful to associate with AP?
Yes, in DMA mode. In PIO mode, it associates, but does not pass any traffic. After a while, there was a critical DMA error, and the driver looped forever trying to communicate with the card.
Are there any messages from bwn(4) related with DMA error? If yes and you reproduce DMA error easily could you please show me the full dmesg?
When it occurs, it is a fatal DMA error, and this streams on the console until reboot. In order to get the card to work again (with either bwn or ndis), I need to power-cycle the laptop.
When it occurs again, I will get you the details and the full dmesg. Do you want a verbose dmesg, or a standard one?
I think a standard one is enough. Thank you.
regards, Weongyo Jeong
_______________________________________________ free...@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "free...@freebsd.org"